Difference between revisions of "Default Configuration Customization"

 
(10 intermediate revisions by 2 users not shown)
Line 8: Line 8:
==Standard Firmware Package==
==Standard Firmware Package==


The configuration information are contained in one file called config.bin located in folder "webuidevkit/xxxxapp" where xxxx depends on the SW package.
The configuration information are contained in one file  
 
► '''config.bin''' located in folder "webuidevkit/xxxxapp" where xxxx depends on the SW package.
 
The same file is copied also in folder "update_rescue".
The same file is copied also in folder "update_rescue".


In order to create  a custom version of the Default Configuration you need to do the following:
In order to create  a custom version of the Default Configuration you need to do the following:


change with binary-editor the configuration values in the config.bin file  
# change with binary-editor the configuration values in the '''config.bin''' file
# run the web2cob command (batch file available in the package) to generate the file '''xxxxapp.cob'''
# copy the config.bin and the xxxxapp.cob file in the update-rescue folder
# run the load_win command (batch file gen.bat available in the package) to generate the '''compound.bin''' file


NOTE: the configuration parameters mapping can be found in the Technical Documention of the Firmware
NOTE: the configuration parameters mapping can be found in the Technical Documention of the Firmware
► run the web2cob command (batch file available in the package) to generate the file xxxxapp.cob
► copy the config.bin and the xxxxapp.cob file in the update-rescue folder
► run the load_win command (batch file available in the package) to generate the compound.bin file


==ABCL Firmware/Application Package==
==ABCL Firmware/Application Package==
Line 28: Line 27:
The configuration information are contained in two different files  
The configuration information are contained in two different files  


► config.bin located in folder "webuidevkit/abclapp" for the common abcl settings
'''config.bin''' located in folder "webuidevkit/abclapp" for the common abcl settings


► appconfig.bin located in folder "bcldevkit" for the application specific settings
'''appconfig.bin''' located in folder "bcldevkit" for the application specific settings


These 2 files are merged in a new config.bin file in folder "update_rescue".
These 2 files are merged in a new config.bin file in folder "update_rescue".


In order to create  a custom version of the Default Configuration you need to do the following:
In order to create  a custom version of the Default Configuration you need to do the following:


# change with binary-editor the configuration values in the config.bin file - NOTE: the configuration parameters mapping can be found in the Technical Documention of the Firmware
# change with binary-editor the configuration values in the '''config.bin''' file (1)
# change with binary-editor the configuration values in the appconfig.bin file - NOTE: the configuration parameters mapping can be found in the EEPROM layout Documention in the same folder
# run the web2cob command (batch file abclapp.bat available in the package) to generate the file '''abclapp.cob'''
# run the web2cob command (batch file abclapp.bat available in the package) to generate the file abclapp.cob  
# change with binary-editor the configuration values in the '''appconfig.bin''' file (2)
# run the tokenizer and web2cob commands (batch file applctns.bat available in the package) to generate the file applications.cob
# run the tokenizer and web2cob commands (batch file applctns.bat available in the package) to generate the file '''applications.cob'''
# merge the two configuration files into one (e.g. use "cat" from command-line: cat config.bin appconfig.bin > config.bin)
# merge the two configuration files into one (e.g. use "cat" from command-line: cat config.bin appconfig.bin > config.bin)
# copy the config.bin, abclapp.cob and the applications.cob file in the update-rescue folder
# copy the config.bin, abclapp.cob and the applications.cob file in the update-rescue folder
# run the load_win command (batch file gen.bat available in the package) to generate the compound.bin file
# run the load_win command (batch file gen.bat available in the package) to generate the '''compound.bin''' file
 
NOTE (1): the configuration parameters mapping can be found in the Technical Documention of the Firmware
 
NOTE (2): the configuration parameters mapping can be found in the EEPROM layout Documention in the same folder
 
'''IMPORTANT: Do not forget to apply "Factory Defaults" after uploading the new binaries onto the device.'''

Latest revision as of 14:13, 17 November 2011

Default Configuration Customization

How to customize the default configuration settings of your Barix Audio product.

WARNING: The following tips are intended only for expert users of Barix products as they may cause misconfiguration of the devices.


Standard Firmware Package

The configuration information are contained in one file

config.bin located in folder "webuidevkit/xxxxapp" where xxxx depends on the SW package.

The same file is copied also in folder "update_rescue".

In order to create a custom version of the Default Configuration you need to do the following:

  1. change with binary-editor the configuration values in the config.bin file
  2. run the web2cob command (batch file available in the package) to generate the file xxxxapp.cob
  3. copy the config.bin and the xxxxapp.cob file in the update-rescue folder
  4. run the load_win command (batch file gen.bat available in the package) to generate the compound.bin file

NOTE: the configuration parameters mapping can be found in the Technical Documention of the Firmware

ABCL Firmware/Application Package

The configuration information are contained in two different files

config.bin located in folder "webuidevkit/abclapp" for the common abcl settings

appconfig.bin located in folder "bcldevkit" for the application specific settings

These 2 files are merged in a new config.bin file in folder "update_rescue".

In order to create a custom version of the Default Configuration you need to do the following:

  1. change with binary-editor the configuration values in the config.bin file (1)
  2. run the web2cob command (batch file abclapp.bat available in the package) to generate the file abclapp.cob
  3. change with binary-editor the configuration values in the appconfig.bin file (2)
  4. run the tokenizer and web2cob commands (batch file applctns.bat available in the package) to generate the file applications.cob
  5. merge the two configuration files into one (e.g. use "cat" from command-line: cat config.bin appconfig.bin > config.bin)
  6. copy the config.bin, abclapp.cob and the applications.cob file in the update-rescue folder
  7. run the load_win command (batch file gen.bat available in the package) to generate the compound.bin file

NOTE (1): the configuration parameters mapping can be found in the Technical Documention of the Firmware

NOTE (2): the configuration parameters mapping can be found in the EEPROM layout Documention in the same folder

IMPORTANT: Do not forget to apply "Factory Defaults" after uploading the new binaries onto the device.