User talk:Achims - Revision history

Achims: /* Modbus Control commands for R6 extension module: */

2009-10-23T11:28:56Z

Modbus Control commands for R6 extension module:

← Older revision		Revision as of 11:28, 23 October 2009
Line 1:		Line 1:
	~~== Modbus Control commands for R6 extension module: ==~~


	~~This commands give you the possibility to control the relays on a R6 extension module via a modbus command send as a hex-file in a tcp stack.~~

	It is easy to connect the R6 extension module to the RS485 interface of a Barix device. You have to wire Pin6 (A) and Pin9 (B) of the DB9 connector to Pin2 (A) and Pin3 (B) of the J1 connector on the R6 extension module.

	~~Additional you have to power up the R6 extension module on Pin4 (+) and Pin5 (-) on J1 connector with an external power supply.~~

	The serial settings for the RS485 interface (Serial 2) should set to a baudrate of 19200 Bd, a data bitrate of 8 bits, parity set to even, 1 stopbit, handshake set to RS485 direction control and the local port to 502.

	Now it is possible to send a hex-file, which includes the modbus command, via tcp to port 502 of the Barix device. This can be done with the NetCat Application (nc ''ip-barix'' ''port'' < ''filename'').


	~~The table shows the modbus commands to control the relays on a R6 extension module:~~

	~~{\| class="wikitable" style="text-align:center" border="1" cellpadding="2"~~

	\|-
	~~! !! !! -Modbus Address- !! -Single Coil- !! -Address HI- !! -Address LO- !! -Values HI- !! -Values LO- !! -CRC LO- !! -CRC HI-~~
	\|-
	~~! rowspan="2"\| -Relay 1-~~
	~~\| -set- \|\| 00 \|\| 05 \|\| 00 \|\| 00 \|\| FF \|\| FF \|\| CD \|\| AB~~
	\|-
	~~\| -reset- \|\| 00 \|\| 05 \|\| 00 \|\| 00 \|\| 00 \|\| 00 \|\| CC \|\| 1B~~
	\|-
	~~! rowspan="2"\| -Relay 2-~~
	~~\| -set- \|\| 00 \|\| 05 \|\| 00 \|\| 01 \|\| FF \|\| FF \|\| 9C \|\| 6B~~
	\|-
	~~\| -reset- \|\| 00 \|\| 05 \|\| 00 \|\| 01 \|\| 00 \|\| 00 \|\| 9D \|\| DB~~
	\|-
	~~! rowspan="2"\| -Relay 3-~~
	~~\| -set- \|\| 00 \|\| 05 \|\| 00 \|\| 02 \|\| FF \|\| FF \|\| 6C \|\| 6B~~
	\|-
	~~\| -reset- \|\| 00 \|\| 05 \|\| 00 \|\| 02 \|\| 00 \|\| 00 \|\| 6D \|\| DB~~
	\|-
	~~! rowspan="2"\| -Relay 4-~~
	~~\| -set- \|\| 00 \|\| 05 \|\| 00 \|\| 03 \|\| FF \|\| FF \|\| 3D \|\| AB~~
	\|-
	~~\| -reset- \|\| 00 \|\| 05 \|\| 00 \|\| 03 \|\| 00 \|\| 00 \|\| 3C \|\| 1B~~
	\|-
	~~! rowspan="2"\| -Relay 5-~~
	~~\| -set- \|\| 00 \|\| 05 \|\| 00 \|\| 04 \|\| FF \|\| FF \|\| 8C \|\| 6A~~
	\|-
	~~\| -reset- \|\| 00 \|\| 05 \|\| 00 \|\| 04 \|\| 00 \|\| 00 \|\| 8D \|\| DA~~
	\|-
	~~! rowspan="2"\| -Relay 6-~~
	~~\| -set- \|\| 00 \|\| 05 \|\| 00 \|\| 05 \|\| FF \|\| FF \|\| DD \|\| AA~~
	\|-
	~~\| -reset- \|\| 00 \|\| 05 \|\| 00 \|\| 05 \|\| 00 \|\| 00 \|\| DC \|\| 1A~~
	\|-
	\|}


	~~Please note: It is necessary to calculate a crc-check-sum for each command and add it to the command itself.~~

	~~Here you can find a online crc-calculator:~~
	~~[http://www.lammertbies.nl/comm/info/crc-calculation.html http://www.lammertbies.nl/comm/info/crc-calculation.html]~~






	ac

Achims: /* Modbus Control commands for R6 extension module: */

2009-10-22T18:54:10Z

Modbus Control commands for R6 extension module:

← Older revision		Revision as of 18:54, 22 October 2009
Line 18:		Line 18:

	\|-		\|-
	! !! !! Modbus Address !! Single Coil !! Address HI !! Address LO !! Values HI !! Values LO !! CRC LO !! CRC HI		! !! !! -Modbus Address- !! -Single Coil- !! -Address HI- !! -Address LO- !! -Values HI- !! -Values LO- !! -CRC LO- !! -CRC HI-
	\|-		\|-
	! rowspan="2"\| Relay 1		! rowspan="2"\| -Relay 1-
	\| ~~Set~~ \|\| 00 \|\| 05 \|\| 00 \|\| 00 \|\| FF \|\| FF \|\| CD \|\| AB		\| -set- \|\| 00 \|\| 05 \|\| 00 \|\| 00 \|\| FF \|\| FF \|\| CD \|\| AB
	\|-		\|-
	\| ~~Reset~~ \|\| 00 \|\| 05 \|\| 00 \|\| 00 \|\| 00 \|\| 00 \|\| CC \|\| 1B		\| -reset- \|\| 00 \|\| 05 \|\| 00 \|\| 00 \|\| 00 \|\| 00 \|\| CC \|\| 1B
	\|-		\|-
	! rowspan="2"\| Relay 2		! rowspan="2"\| -Relay 2-
	\| ~~Set~~ \|\| 00 \|\| 05 \|\| 00 \|\| 01 \|\| FF \|\| FF \|\| 9C \|\| 6B		\| -set- \|\| 00 \|\| 05 \|\| 00 \|\| 01 \|\| FF \|\| FF \|\| 9C \|\| 6B
	\|-		\|-
	\| ~~Reset~~ \|\| 00 \|\| 05 \|\| 00 \|\| 01 \|\| 00 \|\| 00 \|\| 9D \|\| DB		\| -reset- \|\| 00 \|\| 05 \|\| 00 \|\| 01 \|\| 00 \|\| 00 \|\| 9D \|\| DB
	\|-		\|-
	! rowspan="2"\| Relay 3		! rowspan="2"\| -Relay 3-
	\| ~~Set~~ \|\| 00 \|\| 05 \|\| 00 \|\| 02 \|\| FF \|\| FF \|\| 6C \|\| 6B		\| -set- \|\| 00 \|\| 05 \|\| 00 \|\| 02 \|\| FF \|\| FF \|\| 6C \|\| 6B
	\|-		\|-
	\| ~~Reset~~ \|\| 00 \|\| 05 \|\| 00 \|\| 02 \|\| 00 \|\| 00 \|\| 6D \|\| DB		\| -reset- \|\| 00 \|\| 05 \|\| 00 \|\| 02 \|\| 00 \|\| 00 \|\| 6D \|\| DB
	\|-		\|-
	! rowspan="2"\| Relay 4		! rowspan="2"\| -Relay 4-
	\| ~~Set~~ \|\| 00 \|\| 05 \|\| 00 \|\| 03 \|\| FF \|\| FF \|\| 3D \|\| AB		\| -set- \|\| 00 \|\| 05 \|\| 00 \|\| 03 \|\| FF \|\| FF \|\| 3D \|\| AB
	\|-		\|-
	\| ~~Reset~~ \|\| 00 \|\| 05 \|\| 00 \|\| 03 \|\| 00 \|\| 00 \|\| 3C \|\| 1B		\| -reset- \|\| 00 \|\| 05 \|\| 00 \|\| 03 \|\| 00 \|\| 00 \|\| 3C \|\| 1B
	\|-		\|-
	! rowspan="2"\| Relay 5		! rowspan="2"\| -Relay 5-
	\| ~~Set~~ \|\| 00 \|\| 05 \|\| 00 \|\| 04 \|\| FF \|\| FF \|\| 8C \|\| 6A		\| -set- \|\| 00 \|\| 05 \|\| 00 \|\| 04 \|\| FF \|\| FF \|\| 8C \|\| 6A
	\|-		\|-
	\| ~~Reset~~ \|\| 00 \|\| 05 \|\| 00 \|\| 04 \|\| 00 \|\| 00 \|\| 8D \|\| DA		\| -reset- \|\| 00 \|\| 05 \|\| 00 \|\| 04 \|\| 00 \|\| 00 \|\| 8D \|\| DA
	\|-		\|-
	! rowspan="2"\| Relay 6		! rowspan="2"\| -Relay 6-
	\| ~~Set~~ \|\| 00 \|\| 05 \|\| 00 \|\| 05 \|\| FF \|\| FF \|\| DD \|\| AA		\| -set- \|\| 00 \|\| 05 \|\| 00 \|\| 05 \|\| FF \|\| FF \|\| DD \|\| AA
	\|-		\|-
	\| ~~Reset~~ \|\| 00 \|\| 05 \|\| 00 \|\| 05 \|\| 00 \|\| 00 \|\| DC \|\| 1A		\| -reset- \|\| 00 \|\| 05 \|\| 00 \|\| 05 \|\| 00 \|\| 00 \|\| DC \|\| 1A
	\|-		\|-
	\|}		\|}
Line 57:		Line 57:
	Here you can find a online crc-calculator:		Here you can find a online crc-calculator:
	[http://www.lammertbies.nl/comm/info/crc-calculation.html http://www.lammertbies.nl/comm/info/crc-calculation.html]		[http://www.lammertbies.nl/comm/info/crc-calculation.html http://www.lammertbies.nl/comm/info/crc-calculation.html]






	ac		ac

Achims: /* Modbus Control commands for R6 extension module: */

2009-10-22T18:42:32Z

Modbus Control commands for R6 extension module:

← Older revision		Revision as of 18:42, 22 October 2009
Line 58:		Line 58:
	[http://www.lammertbies.nl/comm/info/crc-calculation.html http://www.lammertbies.nl/comm/info/crc-calculation.html]		[http://www.lammertbies.nl/comm/info/crc-calculation.html http://www.lammertbies.nl/comm/info/crc-calculation.html]

	.

			ac

Achims: /* Modbus Control commands for R6 extension module: */

2009-10-22T18:41:05Z

Modbus Control commands for R6 extension module:

← Older revision		Revision as of 18:41, 22 October 2009
Line 8:		Line 8:
	Additional you have to power up the R6 extension module on Pin4 (+) and Pin5 (-) on J1 connector with an external power supply.		Additional you have to power up the R6 extension module on Pin4 (+) and Pin5 (-) on J1 connector with an external power supply.

	The serial settings for the RS485 interface (Serial 2) should set to a baudrate of 19200 Bd, a data bitrate of 8 bits, parity set to even, 1 stopbit, handshake set to RS485 direction control and local port to 502.		The serial settings for the RS485 interface (Serial 2) should set to a baudrate of 19200 Bd, a data bitrate of 8 bits, parity set to even, 1 stopbit, handshake set to RS485 direction control and the local port to 502.

	Now it is possible to send a hex-file, which includes the modbus command, via tcp to port 502 of the Barix device. This can be done with the NetCat Application (nc ''ip-barix'' ''port'' < ''filename'').		Now it is possible to send a hex-file, which includes the modbus command, via tcp to port 502 of the Barix device. This can be done with the NetCat Application (nc ''ip-barix'' ''port'' < ''filename'').

Achims: /* Modbus Control commands for R6 extension module: */

2009-10-22T18:39:04Z

Modbus Control commands for R6 extension module:

← Older revision		Revision as of 18:39, 22 October 2009
Line 51:		Line 51:
	\|-		\|-
	\|}		\|}


	Please note: It is necessary to calculate a crc-check-sum for each command and add it to the command itself.		Please note: It is necessary to calculate a crc-check-sum for each command and add it to the command itself.
Line 56:		Line 57:
	Here you can find a online crc-calculator:		Here you can find a online crc-calculator:
	[http://www.lammertbies.nl/comm/info/crc-calculation.html http://www.lammertbies.nl/comm/info/crc-calculation.html]		[http://www.lammertbies.nl/comm/info/crc-calculation.html http://www.lammertbies.nl/comm/info/crc-calculation.html]

			.

Achims: /* Modbus Control commands for R6 extension module: */

2009-10-22T18:38:29Z

Modbus Control commands for R6 extension module:

← Older revision		Revision as of 18:38, 22 October 2009
Line 13:		Line 13:


	The table shows the modbus commands to control the relays on a R6 extension module.		The table shows the modbus commands to control the relays on a R6 extension module:

	{\| class="wikitable" style="text-align:center" border="1" cellpadding="2"		{\| class="wikitable" style="text-align:center" border="1" cellpadding="2"

	~~\|+ Modbus commands~~
	\|-		\|-
	! !! !! Modbus Address !! Single Coil !! Address HI !! Address LO !! Values HI !! Values LO !! CRC LO !! CRC HI		! !! !! Modbus Address !! Single Coil !! Address HI !! Address LO !! Values HI !! Values LO !! CRC LO !! CRC HI

Achims: /* Modbus Control commands for R6 extension module: */

2009-10-22T18:37:25Z

Modbus Control commands for R6 extension module:

← Older revision		Revision as of 18:37, 22 October 2009
Line 10:		Line 10:
	The serial settings for the RS485 interface (Serial 2) should set to a baudrate of 19200 Bd, a data bitrate of 8 bits, parity set to even, 1 stopbit, handshake set to RS485 direction control and local port to 502.		The serial settings for the RS485 interface (Serial 2) should set to a baudrate of 19200 Bd, a data bitrate of 8 bits, parity set to even, 1 stopbit, handshake set to RS485 direction control and local port to 502.

	Now it is possible to send a hex-file, which includes the modbus command, via tcp to port 502 of the device. This can be done with the NetCat Application (nc ''ip-barix'' ''port'' < ''filename'').		Now it is possible to send a hex-file, which includes the modbus command, via tcp to port 502 of the Barix device. This can be done with the NetCat Application (nc ''ip-barix'' ''port'' < ''filename'').


			The table shows the modbus commands to control the relays on a R6 extension module.

	{\| class="wikitable" style="text-align:center" border="1" cellpadding="2"		{\| class="wikitable" style="text-align:center" border="1" cellpadding="2"

Achims: /* Modbus Control commands for R6 extension module: */

2009-10-22T18:35:48Z

Modbus Control commands for R6 extension module:

← Older revision		Revision as of 18:35, 22 October 2009
Line 6:		Line 6:
	It is easy to connect the R6 extension module to the RS485 interface of a Barix device. You have to wire Pin6 (A) and Pin9 (B) of the DB9 connector to Pin2 (A) and Pin3 (B) of the J1 connector on the R6 extension module.		It is easy to connect the R6 extension module to the RS485 interface of a Barix device. You have to wire Pin6 (A) and Pin9 (B) of the DB9 connector to Pin2 (A) and Pin3 (B) of the J1 connector on the R6 extension module.

	Additional you have to power up the R6 extension module on Pin4 (+) and Pin5 (-) on J1 with an external power supply.		Additional you have to power up the R6 extension module on Pin4 (+) and Pin5 (-) on J1 connector with an external power supply.

	The serial settings for the RS485 interface (Serial 2) should set to a baudrate of 19200 Bd, a data bitrate of 8 bits, parity set to even, 1 stopbit, handshake set to RS485 direction control and local port to 502.		The serial settings for the RS485 interface (Serial 2) should set to a baudrate of 19200 Bd, a data bitrate of 8 bits, parity set to even, 1 stopbit, handshake set to RS485 direction control and local port to 502.

Achims: /* Modbus Control commands for R6 extension module: */

2009-10-22T18:34:43Z

Modbus Control commands for R6 extension module:

← Older revision		Revision as of 18:34, 22 October 2009
Line 6:		Line 6:
	It is easy to connect the R6 extension module to the RS485 interface of a Barix device. You have to wire Pin6 (A) and Pin9 (B) of the DB9 connector to Pin2 (A) and Pin3 (B) of the J1 connector on the R6 extension module.		It is easy to connect the R6 extension module to the RS485 interface of a Barix device. You have to wire Pin6 (A) and Pin9 (B) of the DB9 connector to Pin2 (A) and Pin3 (B) of the J1 connector on the R6 extension module.

	Additional you have to power up the R6 extension module on Pin4 (+) and Pin5 (-) with an external power supply.		Additional you have to power up the R6 extension module on Pin4 (+) and Pin5 (-) on J1 with an external power supply.

	The serial settings for the RS485 interface (Serial 2) should set to a baudrate of 19200 Bd, a data bitrate of 8 bits, parity set to even, 1 stopbit, handshake set to RS485 direction control and local port to 502.		The serial settings for the RS485 interface (Serial 2) should set to a baudrate of 19200 Bd, a data bitrate of 8 bits, parity set to even, 1 stopbit, handshake set to RS485 direction control and local port to 502.

Achims: /* Modbus Control commands for R6 extension module: */

2009-10-22T18:33:19Z

Modbus Control commands for R6 extension module:

← Older revision		Revision as of 18:33, 22 October 2009
Line 8:		Line 8:
	Additional you have to power up the R6 extension module on Pin4 (+) and Pin5 (-) with an external power supply.		Additional you have to power up the R6 extension module on Pin4 (+) and Pin5 (-) with an external power supply.

	The serial settings ~~to use~~ the RS485 interface (Serial 2) should set to 19200 ~~Baud~~, 8 ~~Databit~~, parity set to even, 1 ~~Stopbit~~, ~~Handshake~~ set to RS485 direction control and local port to 502.		The serial settings for the RS485 interface (Serial 2) should set to a baudrate of 19200 Bd, a data bitrate of 8 bits, parity set to even, 1 stopbit, handshake set to RS485 direction control and local port to 502.

	Now it is possible to send a hex-file, which includes the modbus command, via tcp to port 502 of the device. This can be done with the NetCat Application (nc ''ip-barix'' ''port'' < ''filename'').		Now it is possible to send a hex-file, which includes the modbus command, via tcp to port 502 of the device. This can be done with the NetCat Application (nc ''ip-barix'' ''port'' < ''filename'').