IO12-Update - Revision history

Dragan: /* Prerequisites */

2011-02-21T12:55:45Z

Prerequisites

← Older revision		Revision as of 12:55, 21 February 2011
Line 10:		Line 10:
	* Optionally: a serial port (HW or USB2serial) and a serial cross cable (3 wire, DB9 female to DB9 female)		* Optionally: a serial port (HW or USB2serial) and a serial cross cable (3 wire, DB9 female to DB9 female)
	* A [[Barionet 50]] (FW 2.00 or higher) or a [[Barionet\|Barionet 100]] (FW 2.08 or higher)		* A [[Barionet 50]] (FW 2.00 or higher) or a [[Barionet\|Barionet 100]] (FW 2.08 or higher)
	* Modbus Test & Load BCL application: choose '''MBT_Vxx_S.cob''' for serial cable or '''MBT_Vxx_T.cob''' for TCP terminal control (xx= stands for actual version number). Download the MBT file from the ~~barix download section [~~[http://www.barix.com/downloads/MBT_Application_Modbus_Tester_Loader_for_extensions/2711]]		* Modbus Test & Load BCL application: choose '''MBT_Vxx_S.cob''' for serial cable or '''MBT_Vxx_T.cob''' for TCP terminal control (xx= stands for actual version number). Download the MBT file from the [http://www.barix.com/downloads/MBT_Application_Modbus_Tester_Loader_for_extensions/2711 Barix download section]
	* Power supply 9VDC (min.) to 30VDC (max.), to supply both Barionet and IO12, 300mA (min.)		* Power supply 9VDC (min.) to 30VDC (max.), to supply both Barionet and IO12, 300mA (min.)
	* 4pin Extension cable to connect to [[Barionet 50]] or 4 wires to connect to [[Barionet\|Barionet 100]]		* 4pin Extension cable to connect to [[Barionet 50]] or 4 wires to connect to [[Barionet\|Barionet 100]]

Dragan: /* Firmware Update procedure */ corrected hex notations

2011-02-21T12:52:02Z

Firmware Update procedure: corrected hex notations

← Older revision		Revision as of 12:52, 21 February 2011
Line 78:		Line 78:
	#:<code>R0,256,4</code>		#:<code>R0,256,4</code>
	#:<code>READ: 00B3 0008 000C 0052</code>		#:<code>READ: 00B3 0008 000C 0052</code>
	#:The first group of digits tells the HW Type (B3=IO12), the 2nd tells the current version (V8), the 3rd the Serial 1 (~~0xC~~=12 decimal) and the 4th the Serial 2 (~~0x52~~=82 decimal). Both serials can be found on the data plate of the IO12 !		#:The first group (word) of digits tells the HW Type (0x00B3=IO12), the 2nd tells the current version (version 8), the 3rd the Serial 1 (0x000C=12 decimal) and the 4th the Serial 2 (0x0052=82 decimal). Both serials can be found on the data plate of the IO12 !
	#:⇒ If you do NOT receive a reply check the wiring. Another reason for this failure could be the settings of the device. See section [[Barix_IO12#IO12_Defaults_Parameters_Jumper\|IO12 Defaults Parameters Jumper]] on the [[Barix_IO12\|Barix IO12]] wiki page to assume defaults.		#:⇒ If you do NOT receive a reply check the wiring. Another reason for this failure could be the settings of the device. See section [[Barix_IO12#IO12_Defaults_Parameters_Jumper\|IO12 Defaults Parameters Jumper]] on the [[Barix_IO12\|Barix IO12]] wiki page to assume defaults.
	#Now that we know that the connection works we can start with deleting the existing firmware by entering '''F12,82''' (capital F, serial1, comma, serial2)		#Now that we know that the connection works we can start with deleting the existing firmware by entering '''F12,82''' (capital F, serial1, comma, serial2)

Dragan: /* Firmware Update procedure */ added default parameters link

2011-02-21T12:50:01Z

Firmware Update procedure: added default parameters link

← Older revision		Revision as of 12:50, 21 February 2011
Line 79:		Line 79:
	#:<code>READ: 00B3 0008 000C 0052</code>		#:<code>READ: 00B3 0008 000C 0052</code>
	#:The first group of digits tells the HW Type (B3=IO12), the 2nd tells the current version (V8), the 3rd the Serial 1 (0xC=12 decimal) and the 4th the Serial 2 (0x52=82 decimal). Both serials can be found on the data plate of the IO12 !		#:The first group of digits tells the HW Type (B3=IO12), the 2nd tells the current version (V8), the 3rd the Serial 1 (0xC=12 decimal) and the 4th the Serial 2 (0x52=82 decimal). Both serials can be found on the data plate of the IO12 !
			#:⇒ If you do NOT receive a reply check the wiring. Another reason for this failure could be the settings of the device. See section [[Barix_IO12#IO12_Defaults_Parameters_Jumper\|IO12 Defaults Parameters Jumper]] on the [[Barix_IO12\|Barix IO12]] wiki page to assume defaults.
	#Now that we know that the connection works we can start with deleting the existing firmware by entering '''F12,82''' (capital F, serial1, comma, serial2)		#Now that we know that the connection works we can start with deleting the existing firmware by entering '''F12,82''' (capital F, serial1, comma, serial2)
	#:⇒ Make sure you use the correct serial numbers 1 and 2 (decimal values not hex) of '''YOUR''' device !!!		#:⇒ Make sure you use the correct serial numbers 1 and 2 (decimal values not hex) of '''YOUR''' device !!!

Dragan: /* Firmware Update procedure */

2011-02-21T10:45:58Z

Firmware Update procedure

← Older revision		Revision as of 10:45, 21 February 2011
Line 119:		Line 119:
	#:<code>R0,256,4</code>		#:<code>R0,256,4</code>
	#:<code>READ: 00B3 000B 000C 0052</code>		#:<code>READ: 00B3 000B 000C 0052</code>
	#:The second group (word) of digits tells the current firmware version (now ~~0xB = V11~~).		#:The second group (word) of digits tells the current firmware version (now 0x000B stands for version 11).
	#:⇒ If it still says the old version then the update failed. Start over from the beginning.		#:⇒ If it still says the old version then the update failed. Start over from the beginning.
	Gratulations, you succesfully updated the device.		Gratulations, you succesfully updated the device.

Dragan: /* Firmware Update procedure */

2011-02-21T10:44:32Z

Firmware Update procedure

← Older revision		Revision as of 10:44, 21 February 2011
Line 119:		Line 119:
	#:<code>R0,256,4</code>		#:<code>R0,256,4</code>
	#:<code>READ: 00B3 000B 000C 0052</code>		#:<code>READ: 00B3 000B 000C 0052</code>
	#:The second group of digits tells the current firmware version (now 0xB = V11).		#:The second group (word) of digits tells the current firmware version (now 0xB = V11).
	#:⇒ If it still says the old version then the update failed. Start over from the beginning.		#:⇒ If it still says the old version then the update failed. Start over from the beginning.
	Gratulations, you succesfully updated the device.		Gratulations, you succesfully updated the device.

Dragan: /* Firmware Update procedure */ return policy uptaded

2011-02-21T10:38:38Z

Firmware Update procedure: return policy uptaded

← Older revision		Revision as of 10:38, 21 February 2011
Line 86:		Line 86:
	#:<code>Wadr,reg,val \| Radr,reg,num or \| sSadr,coil,val \| bBadr \| Is1,s2 \| Cs1,s2 \| Fs1,s2 \| X ?</code>		#:<code>Wadr,reg,val \| Radr,reg,num or \| sSadr,coil,val \| bBadr \| Is1,s2 \| Cs1,s2 \| Fs1,s2 \| X ?</code>
	#:⇒ Do NOT be fooled by the question mark. The IO12 will carry out the Erase command and after 5 to 10 seconds the PWR LED will go dark.		#:⇒ Do NOT be fooled by the question mark. The IO12 will carry out the Erase command and after 5 to 10 seconds the PWR LED will go dark.
	#::*If the PWR LED stays lit then repeat step 7 carefully.		#::*If the PWR LED stays lit then repeat step 4 carefully.
	#::*If after repeating step 7 the PWR LED stays lit then check if ~~your devices production week information on the data plate (bottom of the device):~~		#::*If after repeating step 4 the PWR LED stays lit then contact Barix support to check if the device must be returned to Barix (via reseller) for factory programming.
	~~#:⇒ If it was produced on or between PW50/10 and PW03/11 then you can NOT updated the device using this MBT method !~~
	~~#:⇒ If this is the case~~ the device must be returned to Barix (via reseller) for factory programming.
	#Hit the '''X''' (capital X) and then hit the '''Enter (&crarr;)''' key to exit the service mode. The terminal shows:		#Hit the '''X''' (capital X) and then hit the '''Enter (&crarr;)''' key to exit the service mode. The terminal shows:
	#:<code>Modbus and X8/R6 Test Application</code>		#:<code>Modbus and X8/R6 Test Application</code>

Dragan: /* Prerequisites */

2011-02-21T09:42:56Z

Prerequisites

← Older revision		Revision as of 09:42, 21 February 2011
Line 10:		Line 10:
	* Optionally: a serial port (HW or USB2serial) and a serial cross cable (3 wire, DB9 female to DB9 female)		* Optionally: a serial port (HW or USB2serial) and a serial cross cable (3 wire, DB9 female to DB9 female)
	* A [[Barionet 50]] (FW 2.00 or higher) or a [[Barionet\|Barionet 100]] (FW 2.08 or higher)		* A [[Barionet 50]] (FW 2.00 or higher) or a [[Barionet\|Barionet 100]] (FW 2.08 or higher)
	* Modbus Test & Load BCL application: choose '''MBT_Vxx_S.cob''' for serial cable or '''MBT_Vxx_T.cob''' for TCP terminal control (xx= stands for actual version number)		* Modbus Test & Load BCL application: choose '''MBT_Vxx_S.cob''' for serial cable or '''MBT_Vxx_T.cob''' for TCP terminal control (xx= stands for actual version number). Download the MBT file from the barix download section [[http://www.barix.com/downloads/MBT_Application_Modbus_Tester_Loader_for_extensions/2711]]
	* Power supply 9VDC (min.) to 30VDC (max.), to supply both Barionet and IO12, 300mA (min.)		* Power supply 9VDC (min.) to 30VDC (max.), to supply both Barionet and IO12, 300mA (min.)
	* 4pin Extension cable to connect to [[Barionet 50]] or 4 wires to connect to [[Barionet\|Barionet 100]]		* 4pin Extension cable to connect to [[Barionet 50]] or 4 wires to connect to [[Barionet\|Barionet 100]]

Dragan: /* Firmware Update procedure */

2011-02-21T08:40:37Z

Firmware Update procedure

← Older revision		Revision as of 08:40, 21 February 2011
Line 104:		Line 104:
	#:<code>end programming</code>		#:<code>end programming</code>
	#:<code>firmware load complete</code>		#:<code>firmware load complete</code>
	#::*If it says "end prgramming" only go ~~back~~ to ~~step 4 and~~ repeat the erase command because it will only accept programming when erased prior to programming		#::*If it says "end prgramming" only go start over to repeat the erase command (step 4) because it will only accept programming when erased prior to programming
	#:⇒ After a seconds the PWR LED will be lit.		#:⇒ After a seconds the PWR LED will be lit.
	#::*If it stays dark power cycle the IO12 (disconnect the power wires, wait 4 seconds and reconnect power wires)		#::*If it stays dark power cycle the IO12 (disconnect the power wires, wait 4 seconds and reconnect power wires)

Dragan: /* Software setup */

2011-02-21T08:38:11Z

Software setup

← Older revision		Revision as of 08:38, 21 February 2011
Line 62:		Line 62:
	# Depending on the kind of application control connection do the following:		# Depending on the kind of application control connection do the following:
	#: If you plan to use the TCP version of the application:		#: If you plan to use the TCP version of the application:
	#: * Load the file '''MBT_Vxx_T.cob''' (xx is the version, at the time of writing: 11) into the Barionet's page WEB4 (Barionet 50: via extended web update, Barionet 100: via tftp), reboot when done and wait 10 seconds		#:* Load the file '''MBT_Vxx_T.cob''' (xx is the version, at the time of writing: 11) into the Barionet's page WEB4 (Barionet 50: via extended web update, Barionet 100: via tftp), reboot when done and wait 10 seconds
	#: * Start a terminal program (Telnet session) and connect via TCP port 12345 to the IP of your Barionet		#:* Start a terminal program (Telnet session) and connect via TCP port 12345 to the IP of your Barionet
	#: If you plan to use the serial version of the application:		#: If you plan to use the serial version of the application:
	#:* Load the file '''MBT_Vxx_S.cob''' (xx is the version, at the time of writing: 11) into the Barionet's page WEB4 (Barionet 50: via extended web update, Barionet 100: via tftp), reboot when done and wait 10 seconds		#:* Load the file '''MBT_Vxx_S.cob''' (xx is the version, at the time of writing: 11) into the Barionet's page WEB4 (Barionet 50: via extended web update, Barionet 100: via tftp), reboot when done and wait 10 seconds

Dragan: /* Software setup */

2011-02-21T08:37:39Z

Software setup

← Older revision		Revision as of 08:37, 21 February 2011
Line 66:		Line 66:
	#: If you plan to use the serial version of the application:		#: If you plan to use the serial version of the application:
	#:* Load the file '''MBT_Vxx_S.cob''' (xx is the version, at the time of writing: 11) into the Barionet's page WEB4 (Barionet 50: via extended web update, Barionet 100: via tftp), reboot when done and wait 10 seconds		#:* Load the file '''MBT_Vxx_S.cob''' (xx is the version, at the time of writing: 11) into the Barionet's page WEB4 (Barionet 50: via extended web update, Barionet 100: via tftp), reboot when done and wait 10 seconds
	#: ** Connect the PC/Mac to the serial port of the Barionet with the cross cable		#:* Connect the PC/Mac to the serial port of the Barionet with the cross cable
	#: ** Start a terminal program with the serial settings 9600,8,N,1 no HW control		#:* Start a terminal program with the serial settings 9600,8,N,1 no HW control


	== Firmware Update procedure ==		== Firmware Update procedure ==