Asterix Server configuration for Relay control - Revision history

StefanG: /* Example configuration of Asterisk Server for controlling Relays on Annuncicom SIP Client */

2013-04-10T13:30:01Z

Example configuration of Asterisk Server for controlling Relays on Annuncicom SIP Client

← Older revision		Revision as of 13:30, 10 April 2013
Line 13:		Line 13:
	AND, sure, you can hide the relay selection from the user also by setting up dial-able extensions within Asterisk which use the same target and just do the relay selection. There is no difference between internal and external extensions in that sense in Asterisk.		AND, sure, you can hide the relay selection from the user also by setting up dial-able extensions within Asterisk which use the same target and just do the relay selection. There is no difference between internal and external extensions in that sense in Asterisk.
	Other SIP based systems work similar.		Other SIP based systems work similar.

			Back to [[Main_Page#Software_Topics]]

Sandra: /* Example configuration of Asterix Server for controlling Relays on Annuncicom SIP Client */

2011-07-21T14:02:32Z

Example configuration of Asterix Server for controlling Relays on Annuncicom SIP Client

← Older revision		Revision as of 14:02, 21 July 2011
Line 1:		Line 1:
	==Example configuration of ~~Asterix~~ Server for controlling Relays on Annuncicom SIP Client==		==Example configuration of Asterisk Server for controlling Relays on Annuncicom SIP Client==

	Here is the actual configuration as a showcase of our company Asterisk server. We use two different extensions, reachable from even outside, which connect to an Annuncicom 1000 and select/deselect the relays at connnection establishment.		Here is the actual configuration as a showcase of our company Asterisk server. We use two different extensions, reachable from even outside, which connect to an Annuncicom 1000 and select/deselect the relays at connnection establishment.

Jrietschel: /* Example configuration of Asterix Server for controlling Relays on Annuncicom SIP Client */

2010-10-26T10:26:29Z

Example configuration of Asterix Server for controlling Relays on Annuncicom SIP Client

← Older revision		Revision as of 10:26, 26 October 2010
Line 4:		Line 4:
	The commands sent (via SIP INFO/RFC2833) are just examples, the complete set is documented with the SIP Client firmware.		The commands sent (via SIP INFO/RFC2833) are just examples, the complete set is documented with the SIP Client firmware.

	In the example below, extension 9999 is an Annuncicom 1000, and by dialling +~~41434332229~~ from external phone line, you will be connected to the Annuncicom and all relays will be reset (off - value 0), in the second line, if you dial +~~41434332228~~, right after connection initiation, relays 1+2 (bit 0 and 1, value 3 in decimal) will be set to on.		In the example below, extension 9999 is an Annuncicom 1000, and by dialling +4143xxxxxxx from external phone line, you will be connected to the Annuncicom and all relays will be reset (off - value 0), in the second line, if you dial +4143xxxxxxy, right after connection initiation, relays 1+2 (bit 0 and 1, value 3 in decimal) will be set to on.

	exten => ~~0434332229~~,1,Dial(SIP/9999,10,D(#20)) ; can be reached from external		exten => 043xxxxxxx,1,Dial(SIP/9999,10,D(#20)) ; can be reached from external
	exten => ~~0434332228~~,1,Dial(SIP/9999,10,D(#23)) ; can be reached from external		exten => 043xxxxxxy,1,Dial(SIP/9999,10,D(#23)) ; can be reached from external

	Of course, you can also send such commands (#27 for example to set relay 1,2,3) while the connection is established from the calling phone, if it supports DTMF and all handling of the incoming phone is set up correctly in Asterisk (that is beyond our scope, standard Asterisk docs explain that well).		Of course, you can also send such commands (#27 for example to set relay 1,2,3) while the connection is established from the calling phone, if it supports DTMF and all handling of the incoming phone is set up correctly in Asterisk (that is beyond our scope, standard Asterisk docs explain that well).

Domenico: New page: ==Example configuration of Asterix Server for controlling Relays on Annuncicom SIP Client== Here is the actual configuration as a showcase of our company Asterisk server. We use two diffe...

2009-09-21T11:35:06Z

New page: ==Example configuration of Asterix Server for controlling Relays on Annuncicom SIP Client== Here is the actual configuration as a showcase of our company Asterisk server. We use two diffe...

New page

==Example configuration of Asterix Server for controlling Relays on Annuncicom SIP Client==

Here is the actual configuration as a showcase of our company Asterisk server. We use two different extensions, reachable from even outside, which connect to an Annuncicom 1000 and select/deselect the relays at connnection establishment.
The commands sent (via SIP INFO/RFC2833) are just examples, the complete set is documented with the SIP Client firmware.

In the example below, extension 9999 is an Annuncicom 1000, and by dialling +41434332229 from external phone line, you will be connected to the Annuncicom and all relays will be reset (off - value 0), in the second line, if you dial +41434332228, right after connection initiation, relays 1+2 (bit 0 and 1, value 3 in decimal) will be set to on.

exten => 0434332229,1,Dial(SIP/9999,10,D(#2*0*)) ; can be reached from external
exten => 0434332228,1,Dial(SIP/9999,10,D(#2*3*)) ; can be reached from external

Of course, you can also send such commands (#2*7* for example to set relay 1,2,3) while the connection is established from the calling phone, if it supports DTMF and all handling of the incoming phone is set up correctly in Asterisk (that is beyond our scope, standard Asterisk docs explain that well).

AND, sure, you can hide the relay selection from the user also by setting up dial-able extensions within Asterisk which use the same target and just do the relay selection. There is no difference between internal and external extensions in that sense in Asterisk.
Other SIP based systems work similar.