Barix Wiki - User contributions [en]

VSC

2012-07-10T00:41:30Z

Sandra: /* VSC - wiring and structure */

== VSC - the Volume Source Control device ==

[[Image:VSC_Web200.gif|frame|Volume Source Control Panel]]

The VSC is an OEM product, manufactured by a well known US home automation manufacturer.
Barix offers the device for use with the Exstreamer and Annuncicom product lines. VSC features a 2-digit 7-segment LED display, a rotary knob and a built-in IR receiver.

== Software support ==
The VSC panel is supported in the Streaming Client software, version >=2.07. It can be used to control the volume and to select the audio channel. The built-in IR receiver can be used in a combination with the Barix Remote Control.

Optionally VSC can be used with a specific BCL software, to control volume, channel and special functions.

== VSC - wiring and structure ==

Wiring: the VSC needs to be connected to the serial port of the Exstreamer: Barix offers a DB9-RJ45 adapter (available through distribution), which allows the use of a standard patch cable to connect the VSC. The internal wiring of the adapter is described below:
Note – you need to also have 2 resistor of value 2.7-4.7kOhm and a zener diode !
Note that Pin 2 and Pin 5 of the DB-9 connector have multiple connections.

{| border="1" cellpadding="3" cellspacing="0"
|'''RJ-45'''
|'''Patch Cable Color'''
|'''DB-9'''
|-
|Pin 1 - nc
|Orange/White
|
|-
|Pin 2 - IR activity
|Orange
|
|-
|Pin 3 - GND
|Green/White
|Pin 5
|-
|Pin 4 - Data B
|Black
|Pin 2
|-
|Pin 5 - Data A
|Black/White
|to Pin 5 via series resistor
|-
|Pin 6 - IR Out
|Green
|to Pin 8
|-
|Pin 7 - GND
|Brown/White
|Pin 5
|-
|Pin 8 - +U (max. 10V)
|Brown
|Pin 4 via zener diode (to reduce the voltage)
|-
|
|
|Pin 3 to pin 2 via series resistor
|-

|-
|}

== VSC setup/configuration ==

It is recommended to use the Streaming Client version >=2.07. Please follow the [[VSC support in the Streaming Client]] HOWTO.

===ABCL software===

VSC configuration: the selector arrow at the back side of the unit must be pointing to “1”.

Software: To use the VSC, you need to install the “ABCL” firmware kit on the Exstreamer, available for download from the Barix Website. You need to select the “BARP-R” (Barix Paging Protocol- Room) Application from the selection. After storing the selection and rebooting, various settings are available in the “Applications” section – these are not discussed here. The VSC is automatically connected.

Operations/Use: With power on, the VSC typically shows “Er” (Error, no valid communications). This message will go away as soon as the Exstreamer has announced the IP address and starts playing the configured default background channel, which is then shown in the display.

Volume control: when the unit is idle and the channel number is shown, turning the button will increase or decrease the volume. The display shows the volume in steps of 5%, up to the value configured as max (100% is displayed as 99). If volume 0 is set, the output will be muted and the display will be switched off after about 5 seconds. At any time, the volume can be turned on again. After 5 seconds of inactivity, the display changes back to the channel display.

Channel selection: to select a channel, the button has to be pressed once. The display now shows “cX”, where X is the current channel number selected. The user can now use the button to dial a new channel number (up to the configured maximum), and the selection is activated after about 1 second or when the button is pressed again.

If configured, a local Instreamer can be selected by dialing to channel “0”, which is displayed as “Lo”.

Back to [[Main Page#Products]]

2009-11-11T16:34:56Z

Sandra:

We say "max 4W", but that is an absolute maximum. The power consumption very much depends on the use of the relays (Relay on - additional power needed to drive and hold the relay).
Without any relays active, the "typical" consumption is between 1W and 1.5W only.

Back to [[FAQ]]

What is the typical Barionet Power Consumption ?

2009-11-11T16:33:26Z

Sandra: New page: We say "max 4W", but that is an absolute maximum. The power consumption very much depends on the use of the relays (Relay on - additional power needed to drive and hold the relay). Withou...

FAQ

2009-11-11T16:32:39Z

Sandra: /* Barionet related questions */

FAQ

2009-11-11T16:32:16Z

Sandra: /* Barionet related questions */

What if my routers don't have a fix IP address from the ISP (Internet service provider) ?

2009-07-26T22:17:50Z

Sandra:

When your routers don't have a fix IP address and the dynamic IP address changes every day, then it makes sense to use a '''DNS name''' because you cannot change the configuration of the Instreamer / Exstreamer every day. DNS translates a unique name to a IP address. On the Internet there are some DNS registration services, '''DYNDNS.org''' is a very popular DNS service and supported by many routers.

Before you can use a DYNDNS – DNS name you have to create a account on www.dyndns.org, and select/register your DNS name. The account and the registration of a DNS name on DYNDNS is free of charge. The name should be a little more specific than 'myhome' and must be unique in the whole world. Once you have created your account and registered a valid DNS name then you have to configure your router so that the router updates the DYNDNS server every time when the router gets a new IP address from the ISP. Check first which services are supported on your router.

Back to [[FAQ]]

Instreamer 100

2009-07-22T16:58:02Z

Sandra:

[[Image:Instreamer100_FrontPlate_Web200.gif|right]]
[[Image:Instreamer100_RearPlate_Web200.gif|right]]

Converts any analog or digital audio source, including tuners and CD players, into high-quality VBR MPEG1 and MPEG2 streams (stereo mode). G.711 and PCM as well (mono mode). The audio is encoded in real-time, and the generated audio stream can be distributed, via an IP-based network or the Internet, to one or more receivers or Shoutcast/Icecast-servers.

Barix Instreamer 100 can be easily managed via a web browser interface using PCs, web pads, PDAs or other web-enabled devices. With serial and Ethernet control APIs, open IP-standards, and the MP3 format, the device can also be integrated with other components.

Connecting the Barix Instreamer 100 to audio equipment is made simple by offering stereo RCA analog inputs as well as optical S/PDIF and coax digital inputs.

More information available in our website:
http://www.barix.com/downloads/Instreamer_Family/81/

Back to [[Main Page#Products]]

How many destinations can I stream to ?

2009-06-25T00:02:44Z

Sandra: /* Control FAQ */

FAQ

2009-06-25T00:02:14Z

Sandra: /* Audio FAQ */

2009-06-24T23:55:01Z

Sandra: New page: Yes it does. To use the SIP application it is necessary to download the ABCL Kit. ABCL (Audio Barix Control Language) is a free programmable language like basic. The ABCL Kit includes a SI...

Yes it does. To use the SIP application it is necessary to download the ABCL Kit. ABCL (Audio Barix Control Language) is a free programmable language like basic. The ABCL Kit includes a SIP Client for the Annuncicom. You can download it from the Download section of Barix website (Within "Software Solutions" category)

Back to [[FAQ]]

Can I build an intercom system with Annuncicom?

2009-06-24T23:54:28Z

Sandra: New page: Yes, use the PS16 as the central station. Follow this howto to set up the system. Back to FAQ

Yes, use the PS16 as the central station. Follow this [[Barix Intercom System|howto]] to set up the system.

Back to [[FAQ]]

2009-06-24T23:35:55Z

Sandra: New page: Sure. All you have to do is assignthe Instreamer an IP address and connect a computer or an Exstreamer right to it with a crossover cable, switch or hub. It will stream directly to the dev...

Sure. All you have to do is assignthe Instreamer an IP address and connect a computer or an Exstreamer right to it with a crossover cable, switch or hub. It will stream directly to the device.

Back to [[FAQ]]